86-411- 82520767
Fax:86-411-82520737
Website:www.py-generator.com
E-mail:sales@dlpy.cn
py.generator@gmail.com
DISPOSAL OF GENERAL TROUBLES
◆Sets start difficultly ◆When the sets do not reflect or rotate slowly when you press the button “start” |
|
Possible reason: |
Treatment method: |
1 Electric consumption is insufficient. |
|
2 Storage accumulator thread and plug become |
|
flexible. |
|
3 The middle relay loses efficiency. |
|
4 Trouble of the starter. |
|
5 It is not smooth that the oil supply |
|
system supports the oil. Do not support the |
|
oil |
|
|
|
◆The engine can rotate at certain speed, but it can't catch fire |
|
Possible reason: |
Treatment method: |
1 The oil chew has no oil to squirt. |
1 Check if there is stop or gas leakage |
(not support the oil smoothly) |
between fuel tank and the oil pumps |
2 The fuel system is permeated by the air |
2 Open the exhaust gas screw and check the |
3 The fuel pumps' time is inaccurate or the |
situation of producing oil. |
fuel pumps are in trouble |
3 Reset the oil pump time. |
|
4 Overhaul or change the oil pump, then try |
|
again. |
◆After starting shut down by oneself |
|
Possible reason: |
Treatment method: |
1 The oil passage is not smooth, the filter |
1 Check the blocked situation of oil |
stops up, the trouble of the oil pump |
passage; change the filter core of the |
2 The empty filter stops up seriously. |
diesel oil in case of necessity. |
3 The oil chew is in trouble. |
2 Check the state of the empty filter. |
4 Temperature is too low. |
3 Change the oil chew. |
|
4 Heat water to start. |
◆Abnormally engine work |
|
◆Black smoke. |
|
Possible reason: |
Treatment method: |
1 The empty filter stops up seriously. |
1 Check whether the empty filter loses |
2 Fuel trademark is incorrect. |
efficiency |
3 Pressure of gas exhaust is too heavy. |
2 Check the quality of the fuel. |
4 The oil pump is in trouble. |
3 Check if the oil chew is in atomized state. |
5 The oil chews stops up |
4 Check the amount of oil supported of the |
6 The compresses strength of the engine jar |
pump and revitalize. |
is insufficient. |
5 Check it is normal that the air cylinder |
◆Emit the blue smoke or white smoke |
|
Possible reason: |
Treatment method: |
1 The trade mark of the lubricating oil is |
1 check whether the engine oil is too rare |
selected improperly, the oil level is too |
and the oil is the range ruled or not. |
high. |
|
2 It is short to the time to start, the |
2 After sets run for much long time without |
temperature of the engine is low. |
treatment, every is ok. |
3 The piston is worn, the increase jade |
3 Check if the interval of the piston ring, |
articles lose efficiency. |
air cylinder and the work of pressurization |
|
device is normal |
◆It is unstable to run |
|
Possible reason: |
Treatment method: |
1 The oil passage is not smooth or there is |
1 Check whether the oil passage or the tie-in |
air. |
it is loose and the filter is stopped up. |
2 The oil pump or the oil chew is in trouble. |
2 Check if oil pump normally gush out oil, |
|
oil pump rack move flexiblly, the oil chews |
are atomized. |
|
3 The part of the air filter is blocked. |
3 Check the clean state of the core of the |
|
empty filter. |
◆There is strange noise in engines |
|
Possible reason: |
Treatment method: |
1 Check the fuel and choose improperly or the |
1 Check the trade mark of the fuel or add |
fuel is bad. |
the reliable diesel oil, then start again. |
2 Check if extrusion of the oil is wrong. |
2 Check if extrusion of the oil is right. |
3 The oil chew broke down |
3 Check whether the oil chew is normal. |
◆Engines are insufficient in power: |
|
Possible reason: |
Treatment method: |
1 Oil passage to support oil is not smooth. |
1 Check if the oil passage that supports the |
|
oil is smooth and leak gas. |
2 High-pressure oil pumps work abnormally |
2 Check and adjust the high-pressure oil pump |
3 The oil chews work abnormally. |
3 Check and change the oil chews. |
4 The air system is blocked. |
4 Check, clean or change the filter core of |
the air. |
|
◆Engine oil pressures is too low or too high |
|
Possible reason: |
Treatment method: |
1 Engine oil SAE value is incorrect |
1 Check whether the trademark of engine oil |
|
is correct. |
2 Manometer shows inaccurately. |
2 Change the manometer to try again. |
3 The engine oil filter is blocked. |
3 Check or change the engine oil filter. |
◆Temperature is too high |
|
Possible reason: |
Treatment method: |
1 It is not normal to the arrange wind |
1 Check whether the work of the water pump is |
cooling system. |
normal, the gasoline economizer could be |
|
opened. |
2 Inaccurately gush out the oil. |
2 Check whether the water tank outside is |
3 Overload for a long time. |
3 Correct it while gushing out the oil. |
stopped and the elasticity of the fan belt. |
4 Check whether load is rational |